quality tires at a great value

Proper wheel alignment is key to prolonging the life of your tires. If your vehicle is misaligned, it can cause your tires to wear unevenly, and you may experience handling problems such as pulling or abnormal vibration. Tires and wheels are aligned and balanced at the factory to provide the longest life and best overall performance. Adjustments to wheel alignment and tire balancing are not necessary on a regular basis. Consider a wheel alignment check if there is unusual tire wear or the vehicle is significantly pulling to one side or the other. A tire that is out of balance often affects ride quality and can shorten the life of tires, bearings, shocks, and other suspension components. If the vehicle is vibrating when driving on a smooth road, the tires and wheels may need to be rebalanced.

Camber is the tilting of the wheels from the vertical when viewed from the front of the vehicle. When the wheels tilt outward at the top, the camber is positive. When the wheel tilts inward at the top, the camber is negative. The amount of tilt is measured in degrees from the vertical. Camber settings influence the directional control and the tire wear.

• Too much positive camber will result in premature tire wear on the outside of the tire and cause excessive wear on the suspension parts.
• Too much negative camber will result in premature tire wear on the inside of the tire and cause excessive wear on the suspension parts.
• Unequal side-to-side camber of 1 degree or more will cause the vehicle to pull or lead to the side with the most positive camber.

Caster is the tilting of the uppermost point of the steering axis either forward or backward, when viewed from the side of the vehicle. A backward tilt is positive and a forward tilt is negative. Caster influences directional control of the steering but does not affect the tire wear. Caster is affected by the vehicle height, therefore it is important to keep the body at its designed height. Overloading the vehicle or a weak or sagging rear spring will affect caster. When the rear of the vehicle is lower than its designated trim height, the front suspension moves to a more positive caster. If the rear of the vehicle is higher than its designated trim height, the front suspension moves to a less positive caster.

With too little positive caster, steering may be touchy at high speeds and wheel returnability may be diminished when coming out of a turn. If one wheel has more positive caster than the other, that wheel will pull toward the center of the vehicle. This condition will cause the vehicle to pull or lead to the side with the least amount of positive caster.

Air is a gas, expanding when heated and contracting when cooled. For most of North America, fall and early winter are especially important times for checking tire pressure as the ambient temperature falls, tire pressure goes down. A good rule of thumb: with every 10 degrees Fahrenheit of temperature change, tire pressure changes about 1 psi higher as temperatures rise, lower as they fall. What happens if a tire is underinflated?

• Premature or irregular wear
• Poor handling
• Reduced fuel economy
• Overheating, which could lead to a blowout

What happens if a tire is overinflated?

• Unusual wear
• Poor handling
• Rough ride
• Greater risk of damage from road hazards

Check your tires at least once a month when the weather is cold (let the vehicle sit for at least 3 hours). The Tire Information Label located on the inside of your doorframe has the recommended cold tire pressure for your vehicle. Learn more about tire load information here. Use a quality gauge. Don't try to eyeball itradial tires may appear fine even when they're underinflated. Look for objects that can get wedged in the treadthey'll work themselves even further into the tire and cause air loss. To make sure you're covered, every check of your tires should include a check of your spare (if available), as well.

The use of nitrogen gas to inflate tires is available through some dealers. Benefits under controlled conditions include:

• A reduction in the loss of tire pressure over time
• A reduction in the variance of tire pressures with temperature changes due to reduction of water vapor concentration
• A reduction of long-term rubber degradation due to a drop in oxygen

Important: These are obtainable performance improvements when relatively pure nitrogen gas is used to inflate tires under controlled conditions. Inflation pressure maintenance of tires is critical for overall tire and vehicle performance. Maintaining the correct inflation pressure allows the tire to perform as intended, including for comfort, fuel economy, stopping distance, cornering, traction, tread wear, and noise. General Motors' stance on use of nitrogen gas in tires: General Motors does not oppose the use of nitrogen gas in tires. We expect the theoretical benefits to be reduced in practical use due to the lack of an existing infrastructure to continuously facilitate inflating tires with nearly pure nitrogen. Even occasional inflation with compressed atmospheric air will negate many of the theoretical benefits. Given those theoretical benefits, practical limitations, and the robust design of GM Original Equipment TPC tires, the realized benefits to our customers of inflating their tires with purified nitrogen are expected to be minimal.

It's a known fact that regular tire rotation extends the life of your tires and improves performance. Tires are rotated to achieve a uniform wear for all tires. Each tire performs different tasks (such as steering in front- versus rear-wheel drive), therefore tires wear at different rates. Tires should be rotated every 7,500 miles to prevent irregular tire wear. It's important to rotate your tires according to the correct tire-rotation pattern. Doing so will prolong the life of your tires and will reduce the risk of sudden tire failure. Front tires encounter different tasks than the rear tires. And a front-wheel-drive car's tires perform different tasks than those on a rear-wheel-drive car. See the Maintenance Schedule section in your Owner's Manual for additional information about your specific vehicle.

If your vehicle has a Tire Pressure Monitoring System, it will need to be reset after each tire rotation. See your Owner's Manual for details. Or, read more about tire pressure.

Tread wear indicators appear when the tires only have 2/32 inch or less of tread remaining. Rubber in tires ages over time. This also applies to the spare tire (if available), even if it is never used. Multiple factors including temperatures, loading conditions, and inflation pressure maintenance affect how fast tires age. Other warning signs that your vehicle will need tire replacement:

• You can see three or more tread wear indicators around the tire
• The tire cord or fabric is showing through the rubber
• The tire tread or sidewall is cracked, cut, or snagged deep enough to show cord or fabric
• The tire has a bulge or split
• The tire has a puncture, cut, or other damage that can't be repaired correctly

Tires age when stored normally mounted on a parked vehicle. Park a vehicle that will be stored for at least a month in a cool, dry, clean area away from direct sunlight to slow aging. The area should be free of grease, gasoline, or other substances that can deteriorate rubber. This also applies to unmounted tires. Parking for an extended period can cause flat spots on the tires that may result in vibrations while driving. When storing a vehicle for more than a month, remove the tires or raise the vehicle to reduce the weight from the tires.